hardware/README.md

@@ -1,144 +1,109 @@
 # RemoteRig — Camera Node Hardware Design
 
-> **Version:** 0.1.0 | **Status:** Draft
+> **Version:** 0.2.0 | **Status:** Draft  
-> **Target:** GoPro Hero 3 Black/Silver + ESP32 D1 Mini + 1000mAh LiPo
+> **Target:** GoPro Hero 3 Black/Silver + ESP8266 + ESP32 + USB power bank
 
 ## Overview
 
-Each camera node is a self-contained unit clipped onto a GoPro Hero 3. It provides:
+Each camera node is two ESP boards in a small case that clips to the tripod/stand. The case **does not attach to the camera** — only to the stand. Powered by a standard USB power bank.
-- Camera control (start/stop recording) via Wi-Fi
-- Status monitoring (battery, storage, recording state)
-- MQTT communication to the central Pi Zero 2 W hub
-- Battery power for both the ESP32 and GoPro
-
-## Physical Assembly
 
 ```
-┌─────────────────────────────────┐
+     ┌─────────────────┐
-│         GoPro Hero 3            │
+     │  USB Power Bank │── USB ──→ GoPro (power only)
-│  ┌─────────────────────────┐    │
+     │  (off-the-shelf)│── USB ──→ ESP32 + ESP8266 (shared)
-│  │      Lens (front)       │    │
+     └─────────────────┘
-│  └─────────────────────────┘    │
+              │
-│  ┌─────────────────────────┐    │
+     ┌────────┴────────┐
-│  │        Screen           │    │
+     │  Tripod Case    │ ← clips to stand leg
-│  └─────────────────────────┘    │
+     │  ┌────────────┐ │
-│                    ┌──────────┐ │
+     │  │ ESP8266    │ │ ← Wi-Fi → GoPro AP (10.5.5.1)
-│    3D Sleeve ─────→│ ESP8266  │ │ ← Camera bridge (GoPro Wi-Fi)
+     │  │ (camera)   │ │
-│                    │ D1 Mini  │ │
+     │  ├────────────┤ │ ← UART between boards
-│                    ├──────────┤ │
+     │  │ ESP32      │ │ ← Wi-Fi → Travel Router
-│                    │ ESP32    │ │ ← MQTT bridge (travel router)
+     │  │ (MQTT)     │ │
-│                    │ Dev      │ │
+     │  └────────────┘ │
-│                    ├──────────┤ │
+     └─────────────────┘
-│                    │ LiPo     │ │ ← Shared power
-│                    │ 1000mAh  │ │
-│                    └──────────┘ │
-└─────────────────────────────────┘
 ```
 
 ## Bill of Materials
 
 | Item | Qty | Cost | Notes |
 |------|-----|------|-------|
-| GoPro Hero 3 Black/Silver | 1 | Already owned | Target camera |
 | ESP32 Dev Board | 1 | ~$5 | MQTT bridge — talks to hub |
 | ESP8266 D1 Mini | 1 | ~$3 | Camera bridge — talks to GoPro |
-| LiPo 3.7V 1000mAh | 1 | ~$8 | 50x34x8mm typical |
+| USB power bank (5000mAh+) | 1 | ~$10 | Powers both boards + GoPro |
-| 3.3V buck converter | 1 | ~$1 | LiPo → both boards (shared VIN) |
+| Micro-USB cable (short) | 2 | ~$2 | Power bank → boards + GoPro |
-| 5V/3A buck converter | 1 | ~$2 | LiPo → GoPro USB (power only) |
+| Jumper wires F-F | 3 | ~$0.25 | UART TX/RX/GND between boards |
-| JST-XH 2-pin connectors | 2 | ~$1 | Battery quick-disconnect |
+| PETG filament | ~25g | ~$0.50 | 3D printed case |
-| Micro-USB right-angle cable | 1 | ~$2 | Buck → GoPro |
+| Velcro strap (small) | 1 | ~$0.25 | Secure power bank to stand |
-| Jumper wires (female-female) | 4 | ~$0.50 | UART + GND between boards |
-| Velcro strap (20cm) | 1 | ~$0.50 | Secure to GoPro |
-| PETG filament | ~35g | ~$0.70 | 3D printed case |
 
-**Total per node:** ~$24
+**Total per node:** ~$21 (+ GoPro already owned)
 
 ## 3D Printed Case
 
-The case consists of three parts (see `hardware/case/remoterig-case.scad`):
+**File:** `hardware/case/tripod-case.scad`
 
-### Part 1: GoPro Sleeve
+Three parts:
-Wraps around the GoPro body with cutouts for:
+1. **Case body** — holds both boards stacked, cable ports, rail for clip
-- Lens (front)
+2. **Case lid** — screw-on cover with ventilation
-- Screen/viewfinder (back)
+3. **Tripod clip** — C-clamp for 20-35mm poles, slides into case rail
-- USB port (side)
-- Bottom mounting fingers
-- Mounting ears for electronics compartment
-
-### Part 2: Electronics Compartment
-Clips onto the sleeve's mounting ears. Holds:
-- ESP32 D1 Mini board (recessed fit)
-- USB cable routing (in → ESP32, out → GoPro)
-- Ventilation slots (top)
-- LED visibility window
-
-### Part 3: Battery Compartment
-Slides under the GoPro. Contains:
-- LiPo battery cavity
-- Cable exits (to ESP32, to GoPro buck converter)
-- Velcro strap slots
 
 ### Print Settings
-- **Material:** PETG (outdoor/heat resistant) or PLA+
+- **Material:** PETG (outdoor/heat) or PLA+
-- **Layer height:** 0.2mm
+- **Layer:** 0.2mm | **Infill:** 20% gyroid
-- **Infill:** 20% gyroid
+- **Supports:** Yes (for clip overhang)
-- **Supports:** Yes (for cable channels)
+- **Post-processing:** M3x8mm screws for lid (4x)
-- **Bed adhesion:** Brim (5mm) for sleeve
-- **Orientation:** Print sleeve on its back, compartments flat
 
 ## Wiring
 
 ```
-LiPo 3.7V
+USB Power Bank
-  ├── JST-XH connector
+  ├── USB-A → Micro-USB cable → ESP32 USB port
+  │                              (powers ESP32, shared 5V rail)
   │
-  ├──→ 3.3V Buck Converter → ESP8266 VIN + GND
+  ├── USB-A → Micro-USB cable → GoPro USB port
-  │                        → ESP32 VIN + GND
+  │                              (power only — no data)
-  │                        (both boards share the same 3.3V rail)
   │
-  └──→ 5V/3A Buck Converter → Micro-USB right-angle → GoPro USB port
+  └── (ESP8266 powered via ESP32 3.3V pin, or via shared USB)
-       (power only — no data over USB)
 
-UART (ESP8266 ↔ ESP32):
+UART (inside case):
   ESP8266 TX (GPIO1)  ──→ ESP32 RX (GPIO16)
   ESP8266 RX (GPIO3)  ←── ESP32 TX (GPIO17)
   ESP8266 GND ─────────── ESP32 GND
 ```
 
-## Wi-Fi Topology (No Cables for Camera Control)
+**Power note:** Both boards can be powered from a single USB cable if the ESP32's VIN/5V pin is bridged to the ESP8266's VIN. Alternatively, use a USB Y-splitter cable.
+
+## Wi-Fi Topology
 
 ```
-GoPro Hero 3 ──(Wi-Fi AP @ 10.5.5.1)──→ ESP32 STA #1
+GoPro Hero 3 ──(AP @ 10.5.5.1)──→ ESP8266 (camera bridge)
-                                            │
+                                        │
-Travel Router ──(Wi-Fi AP)─────────────────→ ESP32 STA #2
+                                   UART │ (inside case)
-(192.168.4.1)                               │
+                                        │
-                                            │
+Travel Router ──(AP)─────────────────→ ESP32 (MQTT bridge)
-                                            └──→ MQTT → Pi Hub (192.168.4.10)
+(192.168.4.1)                           │
+                                        │
+                                   MQTT │
+                                        ▼
+                                   Pi Hub (192.168.4.10)
 ```
 
-The ESP32 has **no wired data connection** to the GoPro. All camera control is over Wi-Fi. The USB cable is **power only**.
+The ESP8266 and GoPro talk over Wi-Fi — **no data cable between them**. The only cable to the GoPro is USB power from the battery pack.
 
-## Enclosure Dimensions
+## Field Setup
 
-| Component | W × H × D (mm) |
+1. **Mount GoPro** on tripod/stand
-|-----------|-----------------|
+2. **Clip case** to tripod leg
-| GoPro Hero 3 | 60 × 42 × 30 |
+3. **Connect power bank** via USB to case + GoPro
-| ESP32 D1 Mini | 34 × 26 × 5 |
+4. **Power on** — ESP32 auto-connects to travel router, ESP8266 auto-connects to GoPro
-| LiPo 1000mAh | 50 × 34 × 8 |
+5. **Monitor** from `http://192.168.4.10:8080`
-| Full assembly | ~70 × 60 × 55 |
 
-## Usage in the Field
+## Case Dimensions
 
-1. **Pre-show:** Charge LiPos, flash ESP32 firmware, verify MQTT connectivity
+| | W × D × H (mm) |
-2. **At venue:** Mount cameras, power on ESP32s (they auto-connect to travel router)
+|---|---|
-3. **Monitoring:** Open `http://192.168.4.10:8080` on laptop/kiosk
+| Case external | ~64 × 38 × 27 |
-4. **Control:** Start/stop recording from dashboard
+| Case internal | ~57 × 31 × 18 |
-5. **Post-show:** Stop recording, power down, swap batteries for next session
+| Fits poles | 20-35mm diameter |
-
+| Total weight | ~50g (case + boards, without power bank) |
-## Future Improvements
-
-- **Hot-swap battery:** Quick-release battery tray with spring contacts
-- **Weather sealing:** O-ring groove in sleeve for outdoor rain protection
-- **Lens hood:** Integrated sun shield for outdoor daytime recording
-- **Mount adapter:** 1/4"-20 tripod mount thread on bottom
-- **Antenna routing:** External antenna connector for improved Wi-Fi range in stadiums

hardware/case/remoterig-case.scad

@@ -1,222 +0,0 @@
-// RemoteRig — GoPro Hero 3 + ESP32 Camera Case
-// ==============================================
-// Sleeve that wraps around GoPro Hero 3 body with ESP32 + LiPo compartment.
-// Designed for: ESP32 D1 Mini, 1000mAh LiPo, GoPro Hero 3 Black/Silver.
-//
-// Print settings:
-//   Material: PETG (outdoor/heat) or PLA+ (indoor)
-//   Layer: 0.2mm | Infill: 20% gyroid | Supports: yes (for cable channels)
-//   Nozzle: 0.4mm | Bed: 60°C (PLA) / 80°C (PETG)
-
-// ── GoPro Hero 3 Body (approximate) ──
-gopro_width  = 60;   // mm — body width
-gopro_height = 42;   // mm — body height (top to bottom)
-gopro_depth  = 30;   // mm — body depth (front to back)
-gopro_lens_dia = 28; // mm — lens protrusion diameter
-gopro_lens_offset = 18; // mm — lens center from top
-
-// ── ESP8266 D1 Mini + ESP32 Dev Board (stacked) ──
-esp8266_width  = 34.2;
-esp8266_height = 25.6;
-esp8266_thick  = 5;       // board + components
-
-esp32_width  = 52;        // ESP32 Dev Board is larger
-esp32_height = 28;
-esp32_thick  = 5;
-
-// Combined stack
-board_width  = max(esp8266_width, esp32_width);
-board_height = max(esp8266_height, esp32_height);
-board_thick  = esp8266_thick + esp32_thick + 3; // 3mm gap between boards
-
-// ── LiPo Battery (1000mAh typical) ──
-lipo_width  = 35;
-lipo_height = 25;
-lipo_thick  = 8;
-
-// ── Case parameters ──
-wall = 2.0;           // case wall thickness
-tolerance = 0.3;      // print tolerance for friction fit
-compartment_height = board_thick + 5; // internal compartment height for stacked boards
-
-// ── Cable channels ──
-cable_dia = 4;        // USB cable diameter
-cable_channel_depth = 3;
-
-// ══════════════════════════════════════════════════════════════
-// MAIN ASSEMBLY
-// ══════════════════════════════════════════════════════════════
-
-// Uncomment the part you want to export:
-gopro_sleeve();
-// translate([0, -20, 0]) electronics_compartment();
-// translate([0, 20, 0]) battery_compartment();
-
-// ══════════════════════════════════════════════════════════════
-// GoPro Sleeve — wraps around the GoPro body
-// ══════════════════════════════════════════════════════════════
-
-module gopro_sleeve() {
-    union() {
-        // Main sleeve body — wraps around GoPro
-        difference() {
-            // Outer shell
-            rounded_cube(
-                gopro_width + wall*2,
-                gopro_height + wall*2,
-                gopro_depth + wall*2,
-                4  // corner radius
-            );
-            
-            // Inner cavity (GoPro body)
-            translate([0, 0, wall])
-            rounded_cube(
-                gopro_width + tolerance,
-                gopro_height + tolerance,
-                gopro_depth + tolerance,
-                3
-            );
-            
-            // Lens cutout (front face)
-            translate([0, gopro_height/2 - gopro_lens_offset, 0])
-            rotate([90, 0, 0])
-            cylinder(d=gopro_lens_dia + 4, h=wall*3, center=true);
-            
-            // Front screen/viewfinder cutout
-            translate([0, gopro_height/2 - gopro_lens_offset - 18, wall*2])
-            cube([gopro_width - 10, gopro_height - 20, wall*4], center=true);
-            
-            // Bottom cutout (for GoPro mounting fingers)
-            translate([0, 0, gopro_depth/2 + wall])
-            cube([gopro_width - 10, wall*4, wall*4], center=true);
-            
-            // USB port access (side)
-            translate([gopro_width/2 + wall, 0, -5])
-            cube([wall*4, 16, 10], center=true);
-            
-            // Cable channel from ESP32 compartment to GoPro USB
-            translate([gopro_width/2 - 5, -gopro_height/2 + 10, -gopro_depth/2 + 5])
-            rotate([0, 90, 0])
-            cylinder(d=cable_dia, h=wall*3, center=true);
-        }
-        
-        // Mounting ears for electronics compartment
-        for (x = [-1, 1]) {
-            translate([x * (gopro_width/2 - 6), -gopro_height/2 - 6, 0])
-            rotate([90, 0, 0])
-            cylinder(d=8, h=10);
-        }
-    }
-}
-
-// ══════════════════════════════════════════════════════════════
-// Electronics Compartment — holds ESP8266 + ESP32 stacked
-// ══════════════════════════════════════════════════════════════
-
-module electronics_compartment() {
-    comp_w = board_width + wall*2 + 8;
-    comp_h = compartment_height + wall*2;
-    comp_d = board_height + wall*2 + 8;
-    
-    difference() {
-        union() {
-            // Main box
-            rounded_cube(comp_w, comp_d, comp_h, 3);
-            
-            // Mounting tabs (match GoPro sleeve ears)
-            for (x = [-1, 1]) {
-                translate([x * (gopro_width/2 - 6), 0, comp_h/2])
-                rotate([0, 90, 0])
-                cylinder(d=6, h=4, center=true);
-            }
-        }
-        
-        // Inner cavity
-        translate([0, 0, wall])
-        rounded_cube(comp_w - wall*2, comp_d - wall*2, comp_h - wall, 2);
-        
-        // Bottom board (ESP32 — larger) recess
-        translate([0, 5, wall + 1])
-        cube([esp32_width + tolerance, esp32_height + tolerance, esp32_thick + 1], center=true);
-        
-        // Top board (ESP8266 — smaller) recess  
-        translate([0, 5, wall + esp32_thick + 4])
-        cube([esp8266_width + tolerance, esp8266_height + tolerance, esp8266_thick + 1], center=true);
-        
-        // UART wire channel (between boards)
-        translate([comp_w/2, 0, wall + esp32_thick + 1])
-        cube([wall*3, 6, 3], center=true);
-        
-        // USB cable entry (power to boards)
-        translate([comp_w/2, 15, comp_h/2])
-        rotate([0, 90, 0])
-        cylinder(d=6, h=wall*3, center=true);
-        
-        // USB cable exit (to GoPro)
-        translate([comp_w/2, -15, comp_h/2])
-        rotate([0, 90, 0])
-        cylinder(d=cable_dia, h=wall*3, center=true);
-        
-        // Ventilation slots
-        for (y = [-1:2:1]) {
-            for (i = [-15:10:15]) {
-                translate([i, y * comp_d/3, comp_h - 2])
-                cube([6, 1.5, wall*2], center=true);
-            }
-        }
-        
-        // LED windows (thin walls for ESP LEDs)
-        translate([0, 0, wall])
-        cube([5, 5, wall], center=true);
-        translate([0, 0, wall + esp32_thick + 4])
-        cube([5, 5, wall], center=true);
-    }
-}
-
-// ══════════════════════════════════════════════════════════════
-// Battery Compartment — holds LiPo under GoPro
-// ══════════════════════════════════════════════════════════════
-
-module battery_compartment() {
-    bat_w = lipo_width + wall*2 + tolerance;
-    bat_d = lipo_height + wall*2 + tolerance;
-    bat_h = lipo_thick + wall*2 + 4;
-    
-    difference() {
-        // Shell
-        rounded_cube(bat_w, bat_d, bat_h, 3);
-        
-        // Battery cavity
-        translate([0, 0, wall])
-        rounded_cube(lipo_width + tolerance, lipo_height + tolerance, lipo_thick + tolerance, 1);
-        
-        // Cable exit (to ESP32 compartment)
-        translate([0, bat_d/2, bat_h/2])
-        rotate([90, 0, 0])
-        cylinder(d=cable_dia, h=wall*3, center=true);
-        
-        // Cable exit (to GoPro USB)
-        translate([bat_w/3, -bat_d/2, bat_h/2])
-        rotate([90, 0, 0])
-        cylinder(d=cable_dia, h=wall*3, center=true);
-        
-        // Strap slots (velcro strap to secure to GoPro)
-        for (x = [-bat_w/3, bat_w/3]) {
-            translate([x, -bat_d/2, bat_h/2])
-            cube([8, wall*4, 3], center=true);
-        }
-    }
-}
-
-// ══════════════════════════════════════════════════════════════
-// Utility: Rounded cube (positive X/Y/Z = full dimensions)
-// ══════════════════════════════════════════════════════════════
-
-module rounded_cube(w, d, h, r) {
-    hull() {
-        for (x = [-1, 1], y = [-1, 1], z = [-1, 1]) {
-            translate([x * (w/2 - r), y * (d/2 - r), z * (h/2 - r)])
-            sphere(r=r, $fn=20);
-        }
-    }
-}

hardware/case/tripod-case.scad

@@ -0,0 +1,201 @@
+// RemoteRig — Dual-ESP Tripod Case
+// =================================
+// Small box that clips onto a tripod leg or light stand pole.
+// Holds ESP8266 D1 Mini + ESP32 Dev Board (stacked).
+// Powered by standard USB battery pack. No camera sleeve needed.
+//
+// Print settings:
+//   Material: PETG | Layer: 0.2mm | Infill: 20% gyroid
+//   Supports: yes (for clip overhang) | Brim: 5mm
+
+// ── Board dimensions ──
+esp8266_w = 34.2; esp8266_d = 25.6; esp8266_h = 5;
+esp32_w   = 52;   esp32_d   = 28;   esp32_h   = 5;
+board_gap = 3; // air gap between stacked boards
+stack_h   = esp8266_h + esp32_h + board_gap;
+inner_w   = max(esp8266_w, esp32_w);
+inner_d   = max(esp8266_d, esp32_d);
+inner_h   = stack_h + 2;
+
+// ── Case parameters ──
+wall     = 2.0;
+tol      = 0.4;
+outer_w  = inner_w + wall*2 + tol*2;
+outer_d  = inner_d + wall*2 + tol*2;
+outer_h  = inner_h + wall*2;
+
+// ── Tripod clip parameters ──
+pole_min_dia = 20;  // smallest pole
+pole_max_dia = 35;  // largest pole
+clip_width   = 12;  // clip width
+clip_thick   = 3;   // clip arm thickness
+clip_grip    = 2;   // grip ridges
+
+// ── Cable ports ──
+usb_port_w = 12; usb_port_h = 6;
+uart_port_w = 6; uart_port_h = 4;
+
+// ══════════════════════════════════════════════════════════════
+// MAIN — render the full case
+// ══════════════════════════════════════════════════════════════
+
+// Uncomment to render individual parts:
+full_case();
+// case_body();
+// case_lid();
+// tripod_clip();
+
+module full_case() {
+    case_body();
+    // Lid positioned above (for visualization)
+    translate([0, 0, outer_h + 2])
+    case_lid();
+    // Clip on the back
+    translate([0, outer_d/2 + pole_max_dia/2 + clip_thick, outer_h/2])
+    tripod_clip();
+}
+
+// ══════════════════════════════════════════════════════════════
+// Case Body — holds both boards, cable ports
+// ══════════════════════════════════════════════════════════════
+
+module case_body() {
+    difference() {
+        // Outer shell
+        rounded_cube(outer_w, outer_d, outer_h, 3);
+        
+        // Inner cavity
+        translate([0, 0, wall])
+        rounded_cube(inner_w + tol, inner_d + tol, inner_h + tol, 2);
+        
+        // ── Board recesses ──
+        
+        // Bottom: ESP32 (larger board)
+        translate([0, 0, wall + 1])
+        cube([esp32_w + tol, esp32_d + tol, esp32_h + 1], center=true);
+        
+        // Top: ESP8266 (smaller board)
+        translate([0, 0, wall + esp32_h + board_gap + 1])
+        cube([esp8266_w + tol, esp8266_d + tol, esp8266_h + 1], center=true);
+        
+        // ── Cable ports ──
+        
+        // USB power IN (from battery pack → ESP32)
+        translate([0, outer_d/2, outer_h/3])
+        cube([usb_port_w, wall*3, usb_port_h], center=true);
+        
+        // USB power OUT (from battery pack → GoPro)
+        translate([0, -outer_d/2, outer_h/3])
+        cube([usb_port_w, wall*3, usb_port_h], center=true);
+        
+        // UART wire channel (ESP8266 → ESP32 internal)
+        translate([outer_w/2, 0, outer_h/2])
+        cube([wall*3, uart_port_w, uart_port_h], center=true);
+        
+        // ── Ventilation slots (top edge) ──
+        for (x = [-outer_w/4, 0, outer_w/4]) {
+            translate([x, 0, outer_h - wall])
+            cube([8, outer_d*0.6, 2], center=true);
+        }
+        
+        // ── Screw posts for lid ──
+        for (x = [-1, 1], y = [-1, 1]) {
+            translate([x*(outer_w/2 - 5), y*(outer_d/2 - 5), outer_h/2])
+            cylinder(d=3.2, h=outer_h, center=true, $fn=16);
+        }
+        
+        // ── LED window (thin spot to see board LEDs) ──
+        translate([-outer_w/4, -outer_d/2, wall])
+        cube([6, 1, 3], center=true);
+    }
+    
+    // ── Tripod clip mount (rail on back) ──
+    translate([0, outer_d/2, outer_h/2])
+    rotate([90, 0, 0])
+    difference() {
+        cube([clip_width + 4, outer_h*0.7, 6], center=true);
+        // T-slot for clip to slide in
+        cube([clip_width + 1, outer_h*0.7 + 1, 4], center=true);
+    }
+}
+
+// ══════════════════════════════════════════════════════════════
+// Case Lid — snap-fit or screw-on cover
+// ══════════════════════════════════════════════════════════════
+
+module case_lid() {
+    difference() {
+        rounded_cube(outer_w, outer_d, wall*2, 2);
+        
+        // Screw holes (match body posts)
+        for (x = [-1, 1], y = [-1, 1]) {
+            translate([x*(outer_w/2 - 5), y*(outer_d/2 - 5), 0])
+            cylinder(d=3.2, h=wall*3, center=true, $fn=16);
+        }
+        
+        // Ventilation slots (match body)
+        for (x = [-outer_w/4, 0, outer_w/4]) {
+            translate([x, 0, 0])
+            cube([8, outer_d*0.6, 3], center=true);
+        }
+    }
+}
+
+// ══════════════════════════════════════════════════════════════
+// Tripod Clip — C-clamp for pole mounting
+// ══════════════════════════════════════════════════════════════
+
+module tripod_clip() {
+    difference() {
+        union() {
+            // Main body
+            hull() {
+                translate([0, -pole_max_dia/2 - clip_thick, 0])
+                cube([clip_width, clip_thick*2, outer_h*0.7], center=true);
+                
+                translate([0, pole_max_dia/2 + clip_thick, 0])
+                cube([clip_width, clip_thick*2, outer_h*0.7], center=true);
+            }
+            
+            // Top arm (flexible)
+            translate([0, -pole_max_dia/2 - clip_thick, outer_h*0.35])
+            cube([clip_width, pole_max_dia + clip_thick*4, clip_thick], center=true);
+            
+            // Bottom arm
+            translate([0, -pole_max_dia/2 - clip_thick, -outer_h*0.35])
+            cube([clip_width, pole_max_dia + clip_thick*4, clip_thick], center=true);
+            
+            // Mounting tab (slides into case rail)
+            translate([0, -pole_max_dia/2 - clip_thick*3, 0])
+            cube([clip_width + 1, clip_thick*2, outer_h*0.7], center=true);
+        }
+        
+        // Pole hole
+        cylinder(d=pole_max_dia + 2, h=outer_h*1.5, center=true, $fn=32);
+        
+        // Grip ridges on inner surface
+        for (z = [-outer_h*0.25, 0, outer_h*0.25]) {
+            translate([0, 0, z])
+            rotate_extrude(angle=180, $fn=32)
+            translate([pole_max_dia/2 + 0.5, 0])
+            circle(d=1);
+        }
+        
+        // Entry slot (pole slides in from front)
+        translate([0, pole_max_dia/2 + clip_thick, 0])
+        cube([clip_width + 2, pole_max_dia + 10, outer_h*0.7], center=true);
+    }
+}
+
+// ══════════════════════════════════════════════════════════════
+// Utility: rounded cube
+// ══════════════════════════════════════════════════════════════
+
+module rounded_cube(w, d, h, r) {
+    hull() {
+        for (x = [-1, 1], y = [-1, 1], z = [-1, 1]) {
+            translate([x*(w/2 - r), y*(d/2 - r), z*(h/2 - r)])
+            sphere(r=r, $fn=20);
+        }
+    }
+}