generated from CubeCraft-Creations/Tracehound
238 lines
10 KiB
OpenSCAD
238 lines
10 KiB
OpenSCAD
// RemoteRig camera node case v4
|
|
// Parametric OpenSCAD prototype for a status-panel camera node enclosure.
|
|
// Units: millimeters. Coordinate system: X=width, Y=depth/front-back, Z=height.
|
|
// Front/service lid is on the -Y face. Rear strap channels are on the +Y face.
|
|
//
|
|
// Prototype assumptions to confirm against purchased parts:
|
|
// - 1.3 inch OLED module/window opening: 31 x 16 mm visible window, 35 x 19 mm panel clearance.
|
|
// - Small rocker switch cutout: 13 x 19 mm rectangular snap-in opening.
|
|
// - LEDs: two 3 mm panel LEDs (PWR + RGB STAT) with 3.2 mm holes.
|
|
// - Boards: ESP32-C3 Super Mini 22.5 x 18 mm, ESP-01S 24.7 x 14.3 x 12 mm.
|
|
|
|
$fn = 48;
|
|
|
|
// ----- Main enclosure parameters -----
|
|
case_w = 68; // external width; room for OLED + LEDs + switch
|
|
case_d = 42; // external depth; board stack + wiring clearance
|
|
case_h = 32; // external height
|
|
wall = 2.2;
|
|
corner_r = 3.0;
|
|
front_recess_d = 2.0; // lid sits in this front pocket, nominally flush
|
|
lid_clearance = 0.35;
|
|
lid_w = case_w - 8;
|
|
lid_h = case_h - 6;
|
|
lid_t = 2.0;
|
|
lid_lip_t = 1.2; // locating lip protrudes inside service opening
|
|
lid_lip_inset = 2.1;
|
|
// Central body opening avoids the four corner screw bosses. Separate local
|
|
// clearances below handle the OLED/switch bodies without cutting away bosses.
|
|
service_opening_w = 46.0;
|
|
service_opening_h = 11.5;
|
|
|
|
// Hardware
|
|
screw_d = 2.4; // M2 self-tapping / pilot; confirm hardware
|
|
screw_head_d = 4.6;
|
|
boss_d = 6.0;
|
|
boss_len = 8.0;
|
|
|
|
// Front panel components
|
|
// OLED values are intentionally conservative prototype placeholders.
|
|
oled_window_w = 31.0;
|
|
oled_window_h = 16.0;
|
|
oled_bezel_w = 35.0; // engraved/recessed visual outline around window
|
|
oled_bezel_h = 19.0;
|
|
led_hole_d = 3.2; // 3 mm LED clearance
|
|
rocker_w = 13.0; // prototype cutout; measure purchased rocker
|
|
rocker_h = 19.0;
|
|
vent_slot_w = 7.0;
|
|
vent_slot_h = 1.7;
|
|
|
|
// Rear reusable cloth zip-tie / Velcro strap channels
|
|
strap_bridge_w = case_w - 12;
|
|
strap_bridge_h = 7.5; // outer raised tab height
|
|
strap_slot_h = 4.2; // strap thickness opening; adjust for cloth ties
|
|
strap_gap_y = 3.2; // clearance behind bridge for strap material
|
|
strap_bridge_y = strap_gap_y + 2.2;
|
|
strap_z1 = 8.5;
|
|
strap_z2 = 23.5;
|
|
|
|
// Cable exit
|
|
cable_notch_w = 13.0;
|
|
cable_notch_h = 6.0;
|
|
|
|
// ----- Utility geometry -----
|
|
module rounded_box(size=[10,10,10], r=2, center_xy=true) {
|
|
// Rounded in XY, straight in Z.
|
|
linear_extrude(height=size[2])
|
|
offset(r=r)
|
|
square([size[0]-2*r, size[1]-2*r], center=center_xy);
|
|
}
|
|
|
|
module y_cylinder(d, h, center=true) {
|
|
rotate([90,0,0]) cylinder(d=d, h=h, center=center);
|
|
}
|
|
|
|
module screw_boss(x, z) {
|
|
translate([x, -case_d/2 + front_recess_d + boss_len/2, z])
|
|
difference() {
|
|
y_cylinder(d=boss_d, h=boss_len);
|
|
y_cylinder(d=screw_d, h=boss_len + 0.8);
|
|
}
|
|
}
|
|
|
|
module strap_bridge(zc) {
|
|
// Raised rear bridge with a smooth-ish strap tunnel through it.
|
|
// It intentionally overlaps the main shell by ~2.2 mm so the STL is a
|
|
// single printable body, not separate coincident strap-tab volumes.
|
|
translate([0, case_d/2 + strap_bridge_y/2 - 2.2, zc - strap_bridge_h/2])
|
|
difference() {
|
|
rounded_box([strap_bridge_w, strap_bridge_y, strap_bridge_h], r=2.0);
|
|
// Through-slot for the cloth tie. It cuts all the way through Y,
|
|
// while leaving side posts that tie the upper/lower rails together.
|
|
// Matching rear-wall cutouts are made in camera_node_body_v4().
|
|
translate([0, 0, (strap_bridge_h - strap_slot_h)/2])
|
|
rounded_box([strap_bridge_w - 8.0, strap_bridge_y + 0.8, strap_slot_h], r=1.2);
|
|
}
|
|
}
|
|
|
|
// ----- Printable body -----
|
|
module camera_node_body_v4() {
|
|
difference() {
|
|
union() {
|
|
difference() {
|
|
union() {
|
|
// Outer shell.
|
|
translate([0,0,0]) rounded_box([case_w, case_d, case_h], r=corner_r);
|
|
|
|
// Rear cloth zip-tie / Velcro strap bridges.
|
|
strap_bridge(strap_z1);
|
|
strap_bridge(strap_z2);
|
|
}
|
|
|
|
// Front recessed lid pocket (shallow, so the lid can sit flush).
|
|
translate([0, -case_d/2 - 0.2, case_h/2])
|
|
cube([lid_w + lid_clearance, front_recess_d + 0.3, lid_h + lid_clearance], center=true);
|
|
|
|
// Through service opening behind the lid, leaving a recessed ledge/frame.
|
|
service_depth = front_recess_d + wall + 2.0;
|
|
translate([0, -case_d/2 + service_depth/2, case_h/2])
|
|
cube([service_opening_w, service_depth + 0.4, service_opening_h], center=true);
|
|
|
|
// Local front clearances for the OLED module and rocker-switch body.
|
|
// These keep the screw-boss corner material intact while still leaving
|
|
// room for front-panel components and wiring to enter the body cavity.
|
|
translate([0, -case_d/2 + service_depth/2, (case_h - lid_h)/2 + lid_h - 9.5])
|
|
cube([oled_bezel_w + 2.0, service_depth + 0.4, oled_bezel_h + 3.0], center=true);
|
|
translate([15.5, -case_d/2 + service_depth/2, (case_h - lid_h)/2 + 12.0])
|
|
cube([rocker_w + 3.0, service_depth + 0.4, rocker_h + 3.0], center=true);
|
|
|
|
// Rear-wall pass-through slots for reusable cloth zip-ties / Velcro.
|
|
// The slots align with the raised bridges, so straps can thread through
|
|
// the back of the case instead of sitting in a closed decorative groove.
|
|
for (zc=[strap_z1, strap_z2])
|
|
translate([0, case_d/2 + 1.0, zc])
|
|
cube([strap_bridge_w - 8.0, 8.0, strap_slot_h], center=true);
|
|
|
|
// Interior electronics cavity: ESP32-C3 Super Mini + ESP-01S plus wiring/service clearance.
|
|
cavity_d = case_d - front_recess_d - 2*wall;
|
|
translate([0, -case_d/2 + front_recess_d + wall + cavity_d/2, case_h/2])
|
|
cube([case_w - 2*wall, cavity_d, case_h - 2*wall], center=true);
|
|
|
|
// Bottom cable exit / strain-relief notch on lower front edge.
|
|
translate([0, -case_d/2 + 2.0, -0.05])
|
|
cube([cable_notch_w, 9.0, cable_notch_h], center=true);
|
|
}
|
|
|
|
// Four protected screw bosses are added after shell hollowing so the
|
|
// electronics cavity cannot cut away the receiving material.
|
|
screw_x = lid_w/2 - 5.0;
|
|
screw_z_low = (case_h - lid_h)/2 + 4.2;
|
|
screw_z_high = case_h - screw_z_low;
|
|
screw_boss(-screw_x, screw_z_low);
|
|
screw_boss( screw_x, screw_z_low);
|
|
screw_boss(-screw_x, screw_z_high);
|
|
screw_boss( screw_x, screw_z_high);
|
|
}
|
|
|
|
// Final body-level pilot holes cut through the front frame into the
|
|
// protected bosses. Without this pass the boss pilot holes can be
|
|
// hidden behind solid frame material.
|
|
screw_x = lid_w/2 - 5.0;
|
|
screw_z_low = (case_h - lid_h)/2 + 4.2;
|
|
screw_z_high = case_h - screw_z_low;
|
|
for (x=[-screw_x, screw_x], z=[screw_z_low, screw_z_high])
|
|
translate([x, -case_d/2 + front_recess_d + boss_len/2, z])
|
|
y_cylinder(d=screw_d, h=boss_len + front_recess_d + 4.0);
|
|
}
|
|
}
|
|
|
|
// ----- Printable front service lid / status panel -----
|
|
module camera_node_lid_v4() {
|
|
difference() {
|
|
union() {
|
|
// Visible flush panel.
|
|
translate([0,0,0]) rounded_box([lid_w, lid_t, lid_h], r=0.65);
|
|
|
|
// Rear locating lip fits inside the central service opening and helps
|
|
// panel alignment. Center it on the body's central opening so it
|
|
// does not collide with lower vent geometry.
|
|
lip_h = service_opening_h - 0.5;
|
|
translate([0, lid_t/2 + lid_lip_t/2 - 0.2, (lid_h - lip_h)/2])
|
|
rounded_box([service_opening_w - 0.5, lid_lip_t, lip_h], r=0.45);
|
|
|
|
// Shallow raised text pads/labels are omitted for print simplicity; add decals or paint-fill.
|
|
}
|
|
|
|
// OLED window and shallow module outline/recess.
|
|
translate([0, -0.2, lid_h - 9.5])
|
|
cube([oled_window_w, lid_t + lid_lip_t + 0.8, oled_window_h], center=true);
|
|
translate([0, -0.35, lid_h - 9.5])
|
|
cube([oled_bezel_w, 0.7, oled_bezel_h], center=true);
|
|
|
|
// LED holes: separate power LED and single RGB status LED.
|
|
translate([-17.0, -0.2, 11.5]) y_cylinder(d=led_hole_d, h=lid_t + lid_lip_t + 1.0);
|
|
translate([-9.0, -0.2, 11.5]) y_cylinder(d=led_hole_d, h=lid_t + lid_lip_t + 1.0);
|
|
|
|
// Rocker switch snap-in opening.
|
|
translate([15.5, -0.2, 12.0])
|
|
cube([rocker_w, lid_t + lid_lip_t + 1.0, rocker_h], center=true);
|
|
|
|
// Lower vent / style slots.
|
|
for (i=[-2:2])
|
|
translate([i*9.5, -0.2, 4.8])
|
|
cube([vent_slot_w, lid_t + lid_lip_t + 1.0, vent_slot_h], center=true);
|
|
|
|
// Screw clearance/counterbore holes.
|
|
screw_x = lid_w/2 - 5.0;
|
|
screw_z_low = 4.2;
|
|
screw_z_high = lid_h - screw_z_low;
|
|
for (x=[-screw_x, screw_x], z=[screw_z_low, screw_z_high]) {
|
|
translate([x, -0.2, z]) y_cylinder(d=screw_d + 0.4, h=lid_t + lid_lip_t + 1.0);
|
|
translate([x, -0.15, z]) y_cylinder(d=screw_head_d, h=1.2);
|
|
}
|
|
}
|
|
}
|
|
|
|
// ----- Non-print preview assembly -----
|
|
module camera_node_preview_v4(show_lid=true) {
|
|
color("lightgray") camera_node_body_v4();
|
|
if (show_lid)
|
|
translate([0, -case_d/2 - lid_t/2 - 0.2, (case_h - lid_h)/2])
|
|
color("gainsboro") camera_node_lid_v4();
|
|
|
|
// Internal board volume guides (not printed): ESP32-C3 and ESP-01S envelopes.
|
|
color([0,0.45,0,0.35]) translate([-13, -1, 9]) cube([22.5, 18, 4], center=true);
|
|
color([0,0.2,0.8,0.35]) translate([13, -1, 20]) cube([24.7, 14.3, 12], center=true);
|
|
}
|
|
|
|
// Select part to render from OpenSCAD CLI with: -D 'part="body"'
|
|
part = "preview"; // "body", "lid", or "preview"
|
|
|
|
if (part == "body") {
|
|
camera_node_body_v4();
|
|
} else if (part == "lid") {
|
|
camera_node_lid_v4();
|
|
} else {
|
|
camera_node_preview_v4();
|
|
}
|