Add web server configuration and enhance camera settings for ESP32-H2C

Cameras/declan-a1-camera.yaml

@@ -31,6 +31,9 @@ wifi:
     ssid: "${friendly_name} Fallback"
     password: !secret fallback_password
 
+web_server:
+  port: 80
+
 captive_portal:
 
 i2c:
@@ -63,15 +66,15 @@ esp32_camera:
   name: ${device_name}
   brightness: 1
   #contrast: 0
-  agc_gain_ceiling: 2X
+  # agc_gain_ceiling: 2X
-  agc_mode: MANUAL
+  # agc_mode: MANUAL
-  agc_value: 5
+  # agc_value: 5
   # ...
 
 esp32_camera_web_server:
-  - port: 80
-    mode: STREAM
   - port: 8080
+    mode: STREAM
+  - port: 8081
     mode: SNAPSHOT
 
 switch:

Cameras/esp32-h2c-camera.yaml

@@ -55,10 +55,10 @@ esp32_camera:
   pixel_clock_pin: GPIO15
 
   # Start conservative for reliability; increase later if stable.
-  resolution: 640x480
+  resolution: 800x600
-  jpeg_quality: 12
+  jpeg_quality: 15
-  max_framerate: 10 fps
+  max_framerate: 20 fps
-  idle_framerate: 0.2 fps
+  idle_framerate: 0.05 fps
   frame_buffer_count: 1
 
   # Common orientation defaults for this module.

home-energy-monitor.yaml

@@ -0,0 +1,161 @@
+substitutions:
+  friendly_name: "Home Energy Monitor"
+  device_name: home-energy-monitor
+  update_time: 10s
+  # SCT-013-000 (100A/50mA) calibration value
+  current_cal: '27518'
+  # Jameco 9VAC Transformer (board v1.3+)
+  voltage_cal: '7305'
+
+esphome:
+  name: ${device_name}
+  friendly_name: ${friendly_name}
+
+esp32:
+  board: nodemcu-32s
+
+# Enable logging
+logger:
+
+# Enable Home Assistant API
+api:
+  encryption:
+    key: !secret api_encryption_key
+
+# Enable OTA updates
+ota:
+  - platform: esphome
+
+wifi:
+  ssid: !secret wifi_ssid
+  password: !secret wifi_password
+  # Optional: static IP for reliability
+  # manual_ip:
+  #   static_ip: 192.168.1.50
+  #   gateway: 192.168.1.1
+  #   subnet: 255.255.255.0
+
+  # Fallback hotspot if Wi-Fi fails
+  ap:
+    ssid: ${device_name}
+    password: !secret wifi_password
+
+captive_portal:
+
+web_server:
+  port: 80
+
+# SPI bus configuration
+spi:
+  clk_pin: 18
+  miso_pin: 19
+  mosi_pin: 23
+
+sensor:
+  # Wi-Fi signal strength
+  - platform: wifi_signal
+    name: ${device_name} WiFi Signal
+    update_interval: 60s
+
+  # ──────────────────────────────────
+  # IC1: Channels 1-3 (CS pin 5)
+  # ──────────────────────────────────
+  - platform: atm90e32
+    cs_pin: 5
+    phase_a:
+      voltage:
+        name: ${device_name} Volts
+        id: ic1Volts
+        accuracy_decimals: 1
+      current:
+        name: ${device_name} CT1 Amps
+        id: ct1Amps
+      power:
+        name: ${device_name} CT1 Watts
+        id: ct1Watts
+      gain_voltage: ${voltage_cal}
+      gain_ct: ${current_cal}
+    phase_b:
+      current:
+        name: ${device_name} CT2 Amps
+        id: ct2Amps
+      power:
+        name: ${device_name} CT2 Watts
+        id: ct2Watts
+      gain_voltage: ${voltage_cal}
+      gain_ct: ${current_cal}
+    phase_c:
+      current:
+        name: ${device_name} CT3 Amps
+        id: ct3Amps
+      power:
+        name: ${device_name} CT3 Watts
+        id: ct3Watts
+      gain_voltage: ${voltage_cal}
+      gain_ct: ${current_cal}
+    frequency:
+      name: ${device_name} Frequency
+    line_frequency: 60Hz
+    gain_pga: 1X
+    update_interval: ${update_time}
+
+  # ──────────────────────────────────
+  # IC2: Channels 4-6 (CS pin 4)
+  # ──────────────────────────────────
+  - platform: atm90e32
+    cs_pin: 4
+    phase_a:
+      current:
+        name: ${device_name} CT4 Amps
+        id: ct4Amps
+      power:
+        name: ${device_name} CT4 Watts
+        id: ct4Watts
+      gain_voltage: ${voltage_cal}
+      gain_ct: ${current_cal}
+    phase_b:
+      current:
+        name: ${device_name} CT5 Amps
+        id: ct5Amps
+      power:
+        name: ${device_name} CT5 Watts
+        id: ct5Watts
+      gain_voltage: ${voltage_cal}
+      gain_ct: ${current_cal}
+    phase_c:
+      current:
+        name: ${device_name} CT6 Amps
+        id: ct6Amps
+      power:
+        name: ${device_name} CT6 Watts
+        id: ct6Watts
+      gain_voltage: ${voltage_cal}
+      gain_ct: ${current_cal}
+    line_frequency: 60Hz
+    gain_pga: 1X
+    update_interval: ${update_time}
+
+  # ──────────────────────────────────
+  # Calculated: Total Home Power
+  # (CT1 = Main Leg 1, CT2 = Main Leg 2)
+  # ──────────────────────────────────
+  - platform: template
+    name: ${device_name} Total Watts
+    id: totalWatts
+    lambda: "return id(ct1Watts).state + id(ct2Watts).state;"
+    accuracy_decimals: 1
+    unit_of_measurement: W
+    device_class: power
+    update_interval: ${update_time}
+
+  - platform: total_daily_energy
+    name: ${device_name} Total Daily Energy
+    power_id: totalWatts
+    unit_of_measurement: kWh
+    accuracy_decimals: 2
+    filters:
+      - multiply: 0.001
+
+time:
+  - platform: homeassistant
+    id: homeassistant_time