generated from CubeCraft-Creations/Tracehound
114 lines
4.6 KiB
Markdown
114 lines
4.6 KiB
Markdown
# RemoteRig — Camera Node Hardware Design
|
||
|
||
> **Version:** 0.2.0 | **Status:** Draft
|
||
> **Target:** GoPro Hero 3 Black/Silver + ESP8266 + ESP32 + USB power bank
|
||
|
||
## Overview
|
||
|
||
Each camera node is two ESP boards in a small case that clips to the tripod/stand. The case **does not attach to the camera** — only to the stand. Powered by a standard USB power bank.
|
||
|
||
```
|
||
┌─────────────────┐
|
||
│ USB Power Bank │── USB ──→ GoPro (power only)
|
||
│ (off-the-shelf)│── USB ──→ ESP32 + ESP8266 (shared)
|
||
└─────────────────┘
|
||
│
|
||
┌────────┴────────┐
|
||
│ Tripod Case │ ← clips to stand leg
|
||
│ ┌────────────┐ │
|
||
│ │ ESP8266 │ │ ← Wi-Fi → GoPro AP (10.5.5.1)
|
||
│ │ (camera) │ │
|
||
│ ├────────────┤ │ ← UART between boards
|
||
│ │ ESP32 │ │ ← Wi-Fi → Travel Router
|
||
│ │ (MQTT) │ │
|
||
│ └────────────┘ │
|
||
└─────────────────┘
|
||
```
|
||
|
||
## Bill of Materials
|
||
|
||
| Item | Qty | Cost | Notes |
|
||
|------|-----|------|-------|
|
||
| ESP32 Dev Board | 1 | ~$5 | MQTT bridge — talks to hub |
|
||
| ESP8266 D1 Mini | 1 | ~$3 | Camera bridge — talks to GoPro |
|
||
| USB power bank (5000mAh+) | 1 | ~$10 | Powers both boards + GoPro |
|
||
| Micro-USB cable (short) | 2 | ~$2 | Power bank → boards + GoPro |
|
||
| Jumper wires F-F | 3 | ~$0.25 | UART TX/RX/GND between boards |
|
||
| PETG filament | ~25g | ~$0.50 | 3D printed case |
|
||
| Velcro strap (small) | 1 | ~$0.25 | Secure power bank to stand |
|
||
|
||
**Total per node:** ~$21 (+ GoPro already owned)
|
||
|
||
## 3D Printed Case
|
||
|
||
**Current source:** `hardware/case/tripod-case-v3.scad`
|
||
**Pipeline:** `hardware/DESIGN_PIPELINE.md`
|
||
|
||
Four exported prototype files:
|
||
1. **Case body** — holds both boards stacked, cable ports, rear dovetail-style receiver
|
||
2. **Case lid** — screw-on cover with ventilation
|
||
3. **Tripod clamp** — separate screw-tightened C-clamp sized around a 35mm stand/pole
|
||
4. **Full preview** — combined visualization STL only, not intended as the print job
|
||
|
||
### Print Settings
|
||
- **Material:** PETG preferred for heat/outdoor use and clamp flex
|
||
- **Layer:** 0.2mm | **Infill:** 20% gyroid minimum; 35%+ recommended for clamp
|
||
- **Supports:** Likely yes for clamp ears / dovetail overhangs depending on slicer orientation
|
||
- **Post-processing:** M3x8mm screws for lid (4x), one M3 screw + M3 nut for clamp tightening
|
||
|
||
## Wiring
|
||
|
||
```
|
||
USB Power Bank
|
||
├── USB-A → Micro-USB cable → ESP32 USB port
|
||
│ (powers ESP32, shared 5V rail)
|
||
│
|
||
├── USB-A → Micro-USB cable → GoPro USB port
|
||
│ (power only — no data)
|
||
│
|
||
└── (ESP8266 powered via ESP32 3.3V pin, or via shared USB)
|
||
|
||
UART (inside case):
|
||
ESP8266 TX (GPIO1) ──→ ESP32 RX (GPIO16)
|
||
ESP8266 RX (GPIO3) ←── ESP32 TX (GPIO17)
|
||
ESP8266 GND ─────────── ESP32 GND
|
||
```
|
||
|
||
**Power note:** Both boards can be powered from a single USB cable if the ESP32's VIN/5V pin is bridged to the ESP8266's VIN. Alternatively, use a USB Y-splitter cable.
|
||
|
||
## Wi-Fi Topology
|
||
|
||
```
|
||
GoPro Hero 3 ──(AP @ 10.5.5.1)──→ ESP8266 (camera bridge)
|
||
│
|
||
UART │ (inside case)
|
||
│
|
||
Travel Router ──(AP)─────────────────→ ESP32 (MQTT bridge)
|
||
(10.60.1.1) │
|
||
│
|
||
MQTT │
|
||
▼
|
||
Pi Hub (10.60.1.56)
|
||
```
|
||
|
||
The ESP8266 and GoPro talk over Wi-Fi — **no data cable between them**. The only cable to the GoPro is USB power from the battery pack.
|
||
|
||
## Field Setup
|
||
|
||
1. **Mount GoPro** on tripod/stand
|
||
2. **Clip case** to tripod leg
|
||
3. **Connect power bank** via USB to case + GoPro
|
||
4. **Power on** — ESP32 auto-connects to travel router, ESP8266 auto-connects to GoPro
|
||
5. **Monitor** from `http://10.60.1.56:8080`
|
||
|
||
## Case Dimensions
|
||
|
||
| | W × D × H (mm) |
|
||
|---|---|
|
||
| Case body external | ~56.8 × 36.6 × 19.0 |
|
||
| Lid external | ~56.8 × 32.8 × 4.0 |
|
||
| Tripod clamp | ~43.0 × 53.5 × 16.0 |
|
||
| Clamp-to-case mount | Two M3 screws through flat mounting plate |
|
||
| Clamp pole fit | Nominal 35mm; smaller poles TBD / may need inserts |
|
||
| Total weight | TBD after prototype print |
|