Update display initialization comments for clarity and accuracy

esphome/cat-medication-tracker.yaml

@@ -0,0 +1,293 @@
+substitutions:
+  name: cat-medication-tracker
+  friendly_name: "Cat Medication Tracker"
+
+esphome:
+  name: ${name}
+  friendly_name: ${friendly_name}
+  includes:
+    - spi_helper.h
+  on_boot:
+    - priority: 100
+      then:
+        - light.turn_on: backlight
+    - priority: -100
+      then:
+        - lambda: |-
+            // MADCTL 0x48: MY=0, MX=1, BGR=1 — correct portrait, no mirror for ESP32-2432S035R
+            // ESP-IDF SPI master API used to bypass ESPHome's buffered display layer
+            spi_device_handle_t disp_fix;
+            spi_device_interface_config_t cfg = {};
+            cfg.clock_speed_hz = 1000000;
+            cfg.mode = 0;
+            cfg.spics_io_num = -1;  // manual CS
+            cfg.queue_size = 1;
+            if (spi_bus_add_device(SPI2_HOST, &cfg, &disp_fix) == ESP_OK) {
+                gpio_set_level((gpio_num_t)15, 0);  // CS low
+                gpio_set_level((gpio_num_t)2, 0);   // DC = command
+                spi_transaction_t t = {};
+                t.length = 8;
+                t.flags = SPI_TRANS_USE_TXDATA;
+                t.tx_data[0] = 0x36;  // MADCTL register
+                spi_device_polling_transmit(disp_fix, &t);
+                gpio_set_level((gpio_num_t)2, 1);   // DC = data
+                t.tx_data[0] = 0x48;  // MY=0, MX=1, BGR=1
+                spi_device_polling_transmit(disp_fix, &t);
+                gpio_set_level((gpio_num_t)15, 1);  // CS high
+                spi_bus_remove_device(disp_fix);
+            }
+        - component.update: my_display
+
+esp32:
+  board: esp32dev
+  framework:
+    type: arduino
+
+logger:
+  level: DEBUG
+  logs:
+    xpt2046: WARN
+
+api:
+  encryption:
+    key: !secret api_encryption_key
+
+ota:
+  platform: esphome
+  password: !secret ota_password
+
+wifi:
+  ssid: !secret wifi_iot_ssid
+  password: !secret wifi_password
+  ap:
+    ssid: "${name}-fallback"
+    password: !secret fallback_password
+
+captive_portal:
+
+time:
+  - platform: homeassistant
+    id: homeassistant_time
+    on_time:
+      - seconds: 0
+        minutes: 0
+        hours: 0
+        then:
+          - switch.turn_off: penelope_medicated
+          - switch.turn_off: tess_medicated
+          - script.execute: update_display
+
+spi:
+  - id: tft_spi
+    clk_pin: GPIO14
+    mosi_pin: GPIO13
+    miso_pin: GPIO12
+
+display:
+  - platform: mipi_spi
+    model: ILI9488
+    spi_id: tft_spi
+    cs_pin: GPIO15
+    dc_pin: GPIO2
+    reset_pin: GPIO4
+    rotation: 0
+    invert_colors: false
+    color_order: bgr
+    data_rate: 10MHz
+    dimensions:
+      width: 320
+      height: 480
+    id: my_display
+    auto_clear_enabled: false
+    update_interval: 2s
+    color_depth: 16
+    buffer_size: 25%
+    lambda: |-
+      // Colors
+      auto red = Color(255, 0, 0);
+      auto green = Color(0, 200, 0);
+      auto light_grey = Color(200, 200, 200);
+      auto white = Color(255, 255, 255);
+      auto black = Color(0, 0, 0);
+      auto dark_grey = Color(80, 80, 80);
+
+      // Fill background
+      it.fill(light_grey);
+
+      // Border: green if all done, red otherwise
+      bool all_done = id(penelope_medicated).state && id(tess_medicated).state;
+      auto border_color = all_done ? green : red;
+
+      int border = 10;
+      it.filled_rectangle(0, 0, 320, border, border_color);
+      it.filled_rectangle(0, 480 - border, 320, border, border_color);
+      it.filled_rectangle(0, 0, border, 480, border_color);
+      it.filled_rectangle(320 - border, 0, border, 480, border_color);
+
+      // Title
+      it.printf(160, 30, id(title_font), black, TextAlign::TOP_CENTER, "Cat Meds");
+
+      // Penelope button
+      int btn_x = 40;
+      int btn_y = 90;
+      int btn_w = 240;
+      int btn_h = 120;
+
+      auto penelope_color = id(penelope_medicated).state ? green : red;
+      it.filled_rectangle(btn_x, btn_y, btn_w, btn_h, penelope_color);
+      it.rectangle(btn_x, btn_y, btn_w, btn_h, dark_grey);
+      it.printf(btn_x + btn_w/2, btn_y + btn_h/2, id(button_font), white, TextAlign::CENTER, "Penelope");
+      if (id(penelope_medicated).state) {
+        it.printf(btn_x + btn_w/2, btn_y + btn_h - 20, id(status_font), white, TextAlign::CENTER, "DONE");
+      }
+
+      // Tess button
+      btn_y = 230;
+      auto tess_color = id(tess_medicated).state ? green : red;
+      it.filled_rectangle(btn_x, btn_y, btn_w, btn_h, tess_color);
+      it.rectangle(btn_x, btn_y, btn_w, btn_h, dark_grey);
+      it.printf(btn_x + btn_w/2, btn_y + btn_h/2, id(button_font), white, TextAlign::CENTER, "Tess");
+      if (id(tess_medicated).state) {
+        it.printf(btn_x + btn_w/2, btn_y + btn_h - 20, id(status_font), white, TextAlign::CENTER, "DONE");
+      }
+
+      // Reset button
+      int reset_x = 110;
+      int reset_y = 395;
+      int reset_w = 100;
+      int reset_h = 55;
+      it.filled_rectangle(reset_x, reset_y, reset_w, reset_h, dark_grey);
+      it.rectangle(reset_x, reset_y, reset_w, reset_h, black);
+      it.printf(reset_x + reset_w/2, reset_y + reset_h/2, id(status_font), white, TextAlign::CENTER, "RESET");
+
+# XPT2046 Touchscreen
+touchscreen:
+  - platform: xpt2046
+    id: my_touchscreen
+    spi_id: tft_spi
+    cs_pin: GPIO33
+    update_interval: 250ms
+    threshold: 1200
+    calibration:
+      x_min: 280
+      x_max: 3850
+      y_min: 340
+      y_max: 3860
+
+# Touch buttons as binary sensors
+binary_sensor:
+  - platform: touchscreen
+    touchscreen_id: my_touchscreen
+    name: "Penelope Button"
+    id: penelope_button
+    x_min: 40
+    x_max: 280
+    y_min: 90
+    y_max: 210
+    on_press:
+      then:
+        - switch.toggle: penelope_medicated
+
+  - platform: touchscreen
+    touchscreen_id: my_touchscreen
+    name: "Tess Button"
+    id: tess_button
+    x_min: 40
+    x_max: 280
+    y_min: 230
+    y_max: 350
+    on_press:
+      then:
+        - switch.toggle: tess_medicated
+
+  - platform: touchscreen
+    touchscreen_id: my_touchscreen
+    name: "Reset Button"
+    id: reset_button
+    x_min: 110
+    x_max: 210
+    y_min: 395
+    y_max: 450
+    on_press:
+      then:
+        - switch.turn_off: penelope_medicated
+        - switch.turn_off: tess_medicated
+
+  - platform: template
+    name: "Penelope Medication Status"
+    lambda: 'return id(penelope_medicated).state;'
+    device_class: running
+    
+  - platform: template
+    name: "Tess Medication Status"
+    lambda: 'return id(tess_medicated).state;'
+    device_class: running
+
+  - platform: template
+    name: "All Cats Medicated"
+    lambda: 'return id(penelope_medicated).state && id(tess_medicated).state;'
+    device_class: running
+
+# Backlight control
+output:
+  - platform: gpio
+    pin: GPIO27
+    id: backlight_pwm
+    inverted: false
+
+light:
+  - platform: binary
+    output: backlight_pwm
+    name: "${friendly_name} Backlight"
+    id: backlight
+    restore_mode: ALWAYS_ON
+
+# Medication state switches (exposed to Home Assistant)
+switch:
+  - platform: template
+    name: "Penelope Medicated"
+    id: penelope_medicated
+    optimistic: true
+    restore_mode: RESTORE_DEFAULT_OFF
+    on_turn_on:
+      - script.execute: update_display
+    on_turn_off:
+      - script.execute: update_display
+
+  - platform: template
+    name: "Tess Medicated"
+    id: tess_medicated
+    optimistic: true
+    restore_mode: RESTORE_DEFAULT_OFF
+    on_turn_on:
+      - script.execute: update_display
+    on_turn_off:
+      - script.execute: update_display
+
+  - platform: template
+    name: "Reset All Medications"
+    id: reset_all
+    optimistic: false
+    turn_on_action:
+      - switch.turn_off: penelope_medicated
+      - switch.turn_off: tess_medicated
+
+# Script to update display
+script:
+  - id: update_display
+    then:
+      - component.update: my_display
+
+# Fonts
+font:
+  - file: "gfonts://Roboto"
+    id: title_font
+    size: 28
+    
+  - file: "gfonts://Roboto"
+    id: button_font
+    size: 24
+    
+  - file: "gfonts://Roboto"
+    id: status_font
+    size: 14

esphome/fdm-exhaust-fan-control.yaml

@@ -35,22 +35,45 @@ captive_portal:
 web_server:
   port: 80
 
+# GPIO Outputs for fan control
+# IMPORTANT: inverted: true because NPN transistor driver inverts the logic
+#   GPIO HIGH -> NPN ON -> Gate LOW -> Fan OFF
+#   GPIO LOW  -> NPN OFF -> Gate HIGH (5V via pull-up) -> Fan ON
 output:
   - platform: gpio
     pin:
-      number: GPIO3
-      inverted: true  # Fix for driver inversion
+      number: GPIO3  # D1 on XIAO
+      inverted: true
     id: fan_80mm_output
+
   - platform: gpio
     pin:
-      number: GPIO4
+      number: GPIO4  # D2 on XIAO
       inverted: true
     id: fan_120mm_output
 
+# Fan entities for Home Assistant
 fan:
   - platform: binary
     name: "80mm Exhaust Fan"
+    id: fan_80mm
     output: fan_80mm_output
+
   - platform: binary
     name: "120mm Exhaust Fan"
+    id: fan_120mm
     output: fan_120mm_output
+
+# Optional: Add a switch to control both fans together
+switch:
+  - platform: template
+    name: "All Fans"
+    id: all_fans
+    turn_on_action:
+      - fan.turn_on: fan_80mm
+      - fan.turn_on: fan_120mm
+    turn_off_action:
+      - fan.turn_off: fan_80mm
+      - fan.turn_off: fan_120mm
+    lambda: |-
+      return id(fan_80mm).state && id(fan_120mm).state;

esphome/litter-box-cam.yaml

@@ -0,0 +1,335 @@
+# =============================================================================
+# LITTER BOX MONITOR - DFRobot ESP32-S3 AI Camera
+# =============================================================================
+
+substitutions:
+  device_name: litter-box-cam
+  friendly_name: "Litter Box Camera"
+
+# -----------------------------------------------------------------------------
+# Core Device Configuration
+# -----------------------------------------------------------------------------
+esphome:
+  name: ${device_name}
+  friendly_name: ${friendly_name}
+  platformio_options:
+    build_flags: "-DBOARD_HAS_PSRAM"
+    board_build.arduino.memory_type: qio_opi
+
+esp32:
+  board: esp32-s3-devkitc-1
+  framework:
+    type: arduino
+    version: latest
+  flash_size: 16MB
+
+# -----------------------------------------------------------------------------
+# PSRAM Configuration (Critical for camera)
+# -----------------------------------------------------------------------------
+psram:
+  mode: octal
+  speed: 80MHz
+
+# -----------------------------------------------------------------------------
+# Logging & API
+# -----------------------------------------------------------------------------
+logger:
+  level: INFO
+
+api:
+  encryption:
+    key: !secret api_encryption_key
+  
+  services:
+    - service: capture_and_analyze
+      then:
+        - script.execute: capture_image_script
+    
+    - service: update_status
+      variables:
+        needs_scooping: bool
+        litter_level_low: bool
+        cat_present: bool
+        cleanliness_score: int
+      then:
+        - lambda: |-
+            id(needs_scooping_sensor).publish_state(needs_scooping);
+            id(litter_level_low_sensor).publish_state(litter_level_low);
+            id(cat_present_sensor).publish_state(cat_present);
+            id(cleanliness_score_sensor).publish_state(cleanliness_score);
+            id(last_analysis_time).publish_state(id(homeassistant_time).now().timestamp);
+            if (cat_present) {
+              id(daily_cat_visits) += 1;
+              id(cat_visits_sensor).publish_state(id(daily_cat_visits));
+            }
+
+ota:
+  - platform: esphome
+    password: !secret ota_password
+
+# -----------------------------------------------------------------------------
+# WiFi Configuration
+# -----------------------------------------------------------------------------
+wifi:
+  ssid: !secret wifi_iot_ssid
+  password: !secret wifi_password
+  
+  ap:
+    ssid: "${device_name}-AP"
+    password: !secret wifi_password
+
+captive_portal:
+
+# -----------------------------------------------------------------------------
+# MQTT Configuration
+# -----------------------------------------------------------------------------
+mqtt:
+  id: mqtt_client
+  broker: !secret mqtt_broker
+  username: !secret mqtt_username
+  password: !secret mqtt_password
+  topic_prefix: litter_box
+
+# -----------------------------------------------------------------------------
+# Time Synchronization
+# -----------------------------------------------------------------------------
+time:
+  - platform: homeassistant
+    id: homeassistant_time
+    on_time:
+      - seconds: 0
+        minutes: 0
+        hours: 0
+        then:
+          - lambda: |-
+              id(daily_cat_visits) = 0;
+              id(cat_visits_sensor).publish_state(0);
+
+# -----------------------------------------------------------------------------
+# Global Variables
+# -----------------------------------------------------------------------------
+globals:
+  - id: daily_cat_visits
+    type: int
+    restore_value: yes
+    initial_value: '0'
+
+  - id: motion_cooldown_active
+    type: bool
+    initial_value: 'false'
+
+  - id: publish_next_image
+    type: bool
+    initial_value: 'false'
+
+# -----------------------------------------------------------------------------
+# Camera Configuration (OV3660 - DFR1154 Specific)
+# -----------------------------------------------------------------------------
+esp32_camera:
+  id: litter_cam
+  name: "Litter Box Camera"
+  
+  # Hardware Interface - DFR1154 Pinout
+  external_clock:
+    pin: GPIO5
+    frequency: 20MHz
+  i2c_pins:
+    sda: GPIO8
+    scl: GPIO9
+  data_pins: [GPIO16, GPIO18, GPIO21, GPIO17, GPIO14, GPIO7, GPIO6, GPIO4]
+  vsync_pin: GPIO1
+  href_pin: GPIO2
+  pixel_clock_pin: GPIO15
+  
+  # Image Parameters
+  max_framerate: 10 fps
+  idle_framerate: 0.1 fps
+  resolution: 800x600
+  jpeg_quality: 10
+  vertical_flip: true
+  horizontal_mirror: false
+  aec_mode: AUTO
+  agc_mode: AUTO
+  wb_mode: AUTO
+  brightness: 0
+  contrast: 1
+  saturation: 0
+  on_image:
+    then:
+      - lambda: |-
+          if (!id(publish_next_image)) return;
+          id(publish_next_image) = false;
+
+          const uint8_t *data = x->get_data();
+          size_t len = x->get_data_length();
+          size_t out_len = 4 * ((len + 2) / 3);
+          char *buf = (char *)malloc(out_len + 1);
+          if (!buf) return;
+
+          static const char b64[] =
+            "ABCDEFGHIJKLMNOPQRSTUVWXYZabcdefghijklmnopqrstuvwxyz0123456789+/";
+          size_t j = 0;
+          for (size_t i = 0; i < len; i += 3) {
+            uint32_t b = ((uint32_t)data[i] << 16);
+            if (i + 1 < len) b |= ((uint32_t)data[i + 1] << 8);
+            if (i + 2 < len) b |= data[i + 2];
+            buf[j++] = b64[(b >> 18) & 0x3F];
+            buf[j++] = b64[(b >> 12) & 0x3F];
+            buf[j++] = (i + 1 < len) ? b64[(b >> 6) & 0x3F] : '=';
+            buf[j++] = (i + 2 < len) ? b64[b & 0x3F] : '=';
+          }
+          buf[j] = '\0';
+
+          id(mqtt_client).publish("litter_box/camera/image", buf);
+          ESP_LOGI("capture", "Published image (%d bytes raw, %d base64)", len, j);
+          id(status_message).publish_state("Image sent for analysis");
+          free(buf);
+
+# Web server for manual viewing
+esp32_camera_web_server:
+  - port: 8080
+    mode: stream
+  - port: 8081
+    mode: snapshot
+
+# -----------------------------------------------------------------------------
+# GPIO Outputs
+# -----------------------------------------------------------------------------
+output:
+  - id: led_status
+    platform: gpio
+    pin: GPIO3
+  
+  - id: ir_led
+    platform: gpio
+    pin: GPIO47
+  
+  - id: speaker_gain
+    platform: gpio
+    pin: GPIO41
+  
+  - id: speaker_mode
+    platform: gpio
+    pin: GPIO40
+
+# -----------------------------------------------------------------------------
+# Lights
+# -----------------------------------------------------------------------------
+light:
+  - platform: binary
+    name: "Status LED"
+    id: status_led
+    output: led_status
+  
+  - platform: binary
+    name: "IR Night Vision"
+    id: ir_night_vision
+    output: ir_led
+    restore_mode: RESTORE_DEFAULT_OFF
+
+# -----------------------------------------------------------------------------
+# Binary Sensors
+# -----------------------------------------------------------------------------
+binary_sensor:
+  - platform: template
+    name: "Motion Detected"
+    id: motion_detected
+    device_class: motion
+  
+  - platform: template
+    name: "Needs Scooping"
+    id: needs_scooping_sensor
+    device_class: problem
+    icon: "mdi:shovel"
+  
+  - platform: template
+    name: "Litter Level Low"
+    id: litter_level_low_sensor
+    device_class: problem
+    icon: "mdi:cup-outline"
+  
+  - platform: template
+    name: "Cat Present"
+    id: cat_present_sensor
+    device_class: occupancy
+    icon: "mdi:cat"
+
+# -----------------------------------------------------------------------------
+# Sensors
+# -----------------------------------------------------------------------------
+sensor:
+  - platform: wifi_signal
+    name: "WiFi Signal"
+    update_interval: 60s
+  
+  - platform: template
+    name: "Cleanliness Score"
+    id: cleanliness_score_sensor
+    unit_of_measurement: "%"
+    icon: "mdi:star"
+    accuracy_decimals: 0
+  
+  - platform: template
+    name: "Daily Cat Visits"
+    id: cat_visits_sensor
+    icon: "mdi:paw"
+    accuracy_decimals: 0
+  
+  - platform: template
+    name: "Last Analysis"
+    id: last_analysis_time
+    device_class: timestamp
+    icon: "mdi:clock-outline"
+
+# -----------------------------------------------------------------------------
+# Text Sensors
+# -----------------------------------------------------------------------------
+text_sensor:
+  - platform: version
+    name: "ESPHome Version"
+  
+  - platform: template
+    name: "Status Message"
+    id: status_message
+    icon: "mdi:message-text"
+
+# -----------------------------------------------------------------------------
+# Switches
+# -----------------------------------------------------------------------------
+switch:
+  - platform: restart
+    name: "Restart Camera"
+  
+  - platform: template
+    name: "Auto Capture Enabled"
+    id: auto_capture_enabled
+    optimistic: true
+    restore_mode: RESTORE_DEFAULT_ON
+
+# -----------------------------------------------------------------------------
+# Buttons
+# -----------------------------------------------------------------------------
+button:
+  - platform: template
+    name: "Capture Now"
+    icon: "mdi:camera"
+    on_press:
+      - script.execute: capture_image_script
+
+# -----------------------------------------------------------------------------
+# Scripts
+# -----------------------------------------------------------------------------
+script:
+  - id: capture_image_script
+    mode: single
+    then:
+      - lambda: 'ESP_LOGI("capture", "Capturing image...");'
+      - light.turn_on: status_led
+      - delay: 200ms
+      - lambda: |-
+          id(publish_next_image) = true;
+          id(litter_cam).request_image(esphome::esp32_camera::SINGLE_SHOT);
+      - light.turn_off: status_led
+      - lambda: 'id(motion_cooldown_active) = true;'
+      - delay: 30s
+      - lambda: 'id(motion_cooldown_active) = false;'

esphome/master_bedroom_remote.yaml

@@ -119,81 +119,57 @@ touchscreen:
       y_min: 340
       y_max: 3860
     on_touch:
-      # Wake backlight if off
       - lambda: |-
-          id(last_interaction_ms) = millis();
+          uint32_t now = millis();
+          id(last_interaction_ms) = now;
+
+          // Wake backlight on first touch only, don't also trigger a button
           if (!id(backlight_is_on)) {
             auto call = id(backlight).turn_on();
             call.perform();
             id(backlight_is_on) = true;
+            id(last_button_press_ms) = now;
+            return;
           }
+
+          // Debounce: ignore repeated touch events within 600ms
+          if ((uint32_t)(now - id(last_button_press_ms)) < 600) return;
+          id(last_button_press_ms) = now;
+
           ESP_LOGD("touch", "Touch at x=%d, y=%d", touch.x, touch.y);
-      # Button 1: Toggle All (top-left)
-      - if:
-          condition:
-            lambda: 'return touch.x >= 20 && touch.x <= 150 && touch.y >= 50 && touch.y <= 130;'
-          then:
-            - lambda: |-
+
+          // Button 1: Toggle All (top-left)
+          if (touch.x >= 20 && touch.x <= 150 && touch.y >= 50 && touch.y <= 130) {
             ESP_LOGD("touch", "Toggle All pressed");
             id(light1_state) = !id(light1_state);
             id(light2_state) = !id(light2_state);
             id(fan_state) = !id(fan_state);
             id(all_state) = id(light1_state) && id(light2_state) && id(fan_state);
-            - homeassistant.service:
-                service: switch.toggle
-                data:
-                  entity_id: ${light_1_entity}
-            - homeassistant.service:
-                service: switch.toggle
-                data:
-                  entity_id: ${light_2_entity}
-            - homeassistant.service:
-                service: switch.toggle
-                data:
-                  entity_id: ${fan_entity}
-            - component.update: my_display
-      # Button 2: Polly's Light (top-right)
-      - if:
-          condition:
-            lambda: 'return touch.x >= 170 && touch.x <= 300 && touch.y >= 50 && touch.y <= 130;'
-          then:
-            - lambda: |-
+            id(svc_toggle_all).execute();
+
+          // Button 2: Polly's Light (top-right)
+          } else if (touch.x >= 170 && touch.x <= 300 && touch.y >= 50 && touch.y <= 130) {
             ESP_LOGD("touch", "Polly's Light pressed");
             id(light1_state) = !id(light1_state);
             id(all_state) = id(light1_state) && id(light2_state) && id(fan_state);
-            - homeassistant.service:
-                service: switch.toggle
-                data:
-                  entity_id: ${light_1_entity}
-            - component.update: my_display
-      # Button 3: Joshua's Light (bottom-left)
-      - if:
-          condition:
-            lambda: 'return touch.x >= 20 && touch.x <= 150 && touch.y >= 150 && touch.y <= 230;'
-          then:
-            - lambda: |-
+            id(svc_toggle_polly).execute();
+
+          // Button 3: Joshua's Light (bottom-left)
+          } else if (touch.x >= 20 && touch.x <= 150 && touch.y >= 150 && touch.y <= 230) {
             ESP_LOGD("touch", "Joshua's Light pressed");
             id(light2_state) = !id(light2_state);
             id(all_state) = id(light1_state) && id(light2_state) && id(fan_state);
-            - homeassistant.service:
-                service: switch.toggle
-                data:
-                  entity_id: ${light_2_entity}
-            - component.update: my_display
-      # Button 4: Ceiling Fan (bottom-right)
-      - if:
-          condition:
-            lambda: 'return touch.x >= 170 && touch.x <= 300 && touch.y >= 150 && touch.y <= 230;'
-          then:
-            - lambda: |-
+            id(svc_toggle_joshua).execute();
+
+          // Button 4: Ceiling Fan (bottom-right)
+          } else if (touch.x >= 170 && touch.x <= 300 && touch.y >= 150 && touch.y <= 230) {
             ESP_LOGD("touch", "Ceiling Fan pressed");
             id(fan_state) = !id(fan_state);
             id(all_state) = id(light1_state) && id(light2_state) && id(fan_state);
-            - homeassistant.service:
-                service: switch.toggle
-                data:
-                  entity_id: ${fan_entity}
-            - component.update: my_display
+            id(svc_toggle_fan).execute();
+          }
+
+          id(my_display).update();
 
 # Backlight control
 output:
@@ -217,6 +193,41 @@ font:
     id: button_font
     size: 20
 
+# Scripts to call HA services (lambdas can't call homeassistant.service directly)
+script:
+  - id: svc_toggle_all
+    then:
+      - homeassistant.service:
+          service: switch.toggle
+          data:
+            entity_id: ${light_1_entity}
+      - homeassistant.service:
+          service: switch.toggle
+          data:
+            entity_id: ${light_2_entity}
+      - homeassistant.service:
+          service: switch.toggle
+          data:
+            entity_id: ${fan_entity}
+  - id: svc_toggle_polly
+    then:
+      - homeassistant.service:
+          service: switch.toggle
+          data:
+            entity_id: ${light_1_entity}
+  - id: svc_toggle_joshua
+    then:
+      - homeassistant.service:
+          service: switch.toggle
+          data:
+            entity_id: ${light_2_entity}
+  - id: svc_toggle_fan
+    then:
+      - homeassistant.service:
+          service: switch.toggle
+          data:
+            entity_id: ${fan_entity}
+
 # Global state tracking
 globals:
   - id: all_state
@@ -234,6 +245,9 @@ globals:
   - id: last_interaction_ms
     type: uint32_t
     initial_value: "0"
+  - id: last_button_press_ms
+    type: uint32_t
+    initial_value: "0"
   - id: backlight_is_on
     type: bool
     initial_value: "true"

esphome/spi_helper.h

@@ -0,0 +1,3 @@
+#pragma once
+#include "driver/spi_master.h"
+#include "driver/gpio.h"